wall industries, inc. 5 watson brook road exeter, nh 03833 603-778-2300 www.wallindustries.com fax 603-778-9797 pssbu58 series 2 pin input connecto r 60 watt, single output ac/dc open frame power supply rev a features single output rohs compliant class i insulation internal emi filter 2-pin input connector output voltage available from 5vdc to 48vdc wide input voltage range: 90~264vac, 47~63hz input surge current, over voltage, and over load protection description the pssbu58 series of ac/dc switching mode power supplies provides 60 watts of continuous output power in an open frame constructed design. this series has single output supplies with a universal input range of 90~264vac. these units are ideally s uited for use in portable equipment as well as many other applicati ons. all models meet cispr-22 cla ss b emission limits and comply with new ce requirements. all models are input surge current, output voltage, and over load protected. all units are also 100% burn-in tested. specifications: pssbu58 series all specifications are based on 25c, nominal input volt age, and maximum output current unless otherwise noted. we reserve the right to change specific ations based on te chnological advances. specification test conditions min nom max unit input (v in ) operating voltage range 90 264 vac input frequency 47 63 hz input current (low line) io = full load, vin = 115vac 1.2 a input current (high line) io = full load, vin = 230vac 0.6 a inrush current (low line) io = full load, 25c, cool start, vin = 115vac 12 15 a inrush current (high line) io = full load, 25c, cool start, vin = 230vac 26 30 a safety ground leakage current io = full load, vin = 240vac 0.4 0.75 ma start-up time io = full load, vin = 100vac 0.3 1 2 s output (v o ) output voltage range see rating chart load regulation vin = 230vac 3 5 % line regulation io = full load 0.5 1 % output power vin = 90 to 264vac 0 60 w output current range see rating chart ripple & noise (peak to peak) full load, vin = 90vac 0.5 1 % transient response time io = full load to half load, vin = 100vac 4 ms hold-up time io = full load, vin = 110vac 12 ms protection over voltage protection 112 132 % over current protection 110 150 % general efficiency io = full load, vin = 230vac 80 90 % dielectric withstanding voltage for primary to secondary primary to secondary 4242 vdc dielectric withstanding voltage for primary to ground primary to ground 2121 vdc isolation resistance test voltage = 500vdc 50 m ? no load power consumption no load, vin = 240vac 0.1 0.5 w environmental operating temperature derate linearly from 100% load at 40c to 50% load at 70c 0 +70 c storage temperature -40 +85 c relative humidity 5 95 % temperature coefficient all outputs -0.04 +0.04 %/c mtbf operating temperature at 25c, calculated per mil-hdbk-217f 100,000 hours physical weight approximately 140 grams dimensions 4.00(l) x 2.00(w) x 1.00(h) inches 101.6(l) x 50.8(w) x 25.4(h) mm safety emi requirements for cispr-22 vin = 220vac b class emi requirements for fcc part-15 vin = 110vac b class
wall industries, inc. 5 watson brook road exeter, nh 03833 603-778-2300 www.wallindustries.com fax 603-778-9797 pssbu58 series 2 pin input connecto r 60 watt, single output ac/dc open frame power supply rev a model selection table model number preset voltage output voltage range output current range total regulation max output power pssbu58-102 6 vdc 5 ~ 6 vdc 8.00 ~ 6.66a 5% 40w PSSBU58-103 8 vdc 6 ~ 8 vdc 8.00 ~ 6.00a 5% 48w pssbu58-104 11 vdc 8 ~ 11 vdc 6.87 ~ 5.00a 5% 55w pssbu58-105 13 vdc 11 ~ 13 vdc 5.45 ~ 4.61a 5% 60w pssbu58-106 16 vdc 13 ~ 16 vdc 4.23 ~ 3.43a 5% 60w pssbu58-107 21 vdc 16 ~ 21 vdc 3.75 ~ 2.85a 5% 60w pssbu58-108 27 vdc 21 ~ 27 vdc 2.85 ~ 2.22a 3% 60w pssbu58-109 33 vdc 27 ~ 33 vdc 2.22 ~ 1.81a 3% 60w pssbu58-110 40 vdc 33 ~ 40 vdc 1.81 ~ 1.50a 3% 60w pssbu58-111 48 vdc 40 ~ 48 vdc 1.50 ~ 1.20a 2% 60w notes 1. the output voltage is specified as a range (ex: 40 ~ 48vdc); the preset voltage will be set as standard models if nothing different is requested. please contact factory for ordering details. 2. input connector mates with molex housing 35977-0300 and molex 35922 series crimp terminal. mechanical drawing unit: inches (mm) pin connections pin single output 1 out 2 out 3 out 4 rtn 5 rtn 6 rtn p/n: pssbu58-xxx-h3 or pssbu-xxx-h4 mechanical options options h3 h4 mounting holes 0.13 (3.20.5) 0.16 (4.00.5) a 0.12 (3.150.5) 0.17 (4.30.5) b 3.75 (95.30.5) 3.66 (93.00.5) c 0.12 (3.150.5) 0.17 (4.30.5) d 1.75 (44.50.5) 1.69 (42.80.5) input connector mates with molex housing 35977-0300 and molex 35922 series crimp terminal.
|
